DIY smartphone stand made from clips and paper

Home House and cottage Do it yourself

The stand is a useful and convenient thing in everyday life. For example, phones or tablets, which have become an integral part of our daily lives, are a little inconvenient to use in a hospital setting. If you do not have a branded or suitable case that can secure the gadget in an inclined position, then you will have to hold it with your hands. This is inconvenient when watching a movie for a long time, while eating or reading for a long time.

The best solution to this problem may be to purchase a stand specifically designed for this purpose. But sometimes we need it right now, or we simply feel sorry for the money for a seemingly temporary thing. In this case, you can make a stand yourself from available materials. It does not take a lot of time! A couple of minutes and you can comfortably sit in front of the screen of your gadget, while freeing your hands.

In this article we will rely primarily on options for phone stands, but they can also be slightly modernized and used for tablets, books, even for pictures or plates. It all depends only on your imagination. But if she is sleeping, then there is nothing wrong with it. The options proposed in the article are discussed in detail, and it will not be difficult for you to slightly increase the dimensions specifically for the thing for which you are making a stand.

Handy materials to help

You can make a stand yourself from scrap materials. Almost any material you have at home is suitable for this. It could be:

Fastener for car

You can also use paper clips to make a budget phone stand for your car. To do this, you need to have the following tools with you:

2 stationery erasers;
2 paper clips;
spray paint.

It is important to take the process seriously, because the car is in motion, which creates vibration. If you connect the elements poorly, the smartphone holder will simply fall apart.

Stages of making a smartphone holder for a car:

Bend the larger half of the paperclip at a right angle.
Align the bent part and then bend it. As a result, the paper clip takes on a zigzag shape.
Bend the top part of the zigzag so that it turns into a small hook.
Wrap the bottom ponytail with a rubber band.
With the second paperclip, all actions need to be duplicated.
The final touch is to paint the blank black from the can, which will give the holder a more beautiful and stylish look, suitable for a car panel.

Now all that remains is to secure the painted and dried parts by inserting the hooks into the car vent and hooking them so that the hooks hold the stand, and the parts of the paper clips wrapped with rubber band are on the outside and protrude forward. The smartphone is installed on them. In this simple way, with minimal time and material, you can make a smartphone holder for your car.

Don’t forget that comfort comes from pleasant little things. For a good mood and comfort, people surround themselves with functional, beautiful and stylish things. And it’s not at all necessary to spend fabulous sums on designer items and accessories. It is obvious that you can create useful and beautiful things from scrap materials with your own hands.

The ability to use surrounding objects in a non-standard way can not only help out in a difficult situation, but also give you unique things. The same paper clips can be used in the most unexpected way - as a bookmark in a diary, you can use it to pin up your hair, or you can replace a lost holder on a Christmas tree decoration for the New Year. And make a smartphone stand from a discount card, plywood, cardboard or even paper.

Phone stand made from pencils

In order to assemble this structure, you will need:

6 pencils
4 rubber bands

Despite the intricate appearance, this design is very easy to assemble. The idea is that two pencils are held together at the ends with an elastic band, and the third pencil is inserted between the turns of the rubber band. The result is a geometric figure - a tetrahedron. If you still have questions about how to make this version of the stand, then use the example below.

The picture clearly shows how the pencils are held together.

To avoid slipping and make the stand more stable, use pencils with erasers at the ends.

Paper ideas

If you are a fairly creative person, then you can make a stand for your phone or even as a gift from modules. To do this, you will need to master the technique of modular origami.

To begin with, ready-made multi-colored modules are prepared. Next, the blanks begin to be fastened together into various shapes and figures. For example, in a circle, oval, square, and, depending on the initial idea, a full-fledged stand is gradually assembled from the modules. The phone is placed in the center of such a stand.

The fastest disassembled and assembled phone stand is made from office clips. Such clamps can be found in every office, where they are most likely to be needed for our device. At lunchtime you decided to check out the latest news, find out what’s happening in the world, but it’s inconvenient to hold your phone in your hands all the time.

Take two clamps, fasten them together and that’s it! A pleasant time is guaranteed.

If you don’t have office clips at hand, then paper clips, which are no different from office clips, will do. Paper clips make the same great stand.

A stand of binders will entertain your lunch or leisure time. Let's see how to do it:

It also won’t take much time to implement an interesting idea made from newspaper tubes. And such a product will be an excellent gift, as it looks like a real hand-made store item.

In order for the product to have a neat appearance, the paper tubes must be very thin. The final appearance of such a stand depends only on your imagination - any colors, patterns, ornaments, from classic ones reminiscent of wood to the brightest modern colors. You can decorate as much as you like. The master class shown in the video clearly explains how to do this.

Related article: How to weave animals from rubber bands on a machine and on a slingshot for beginners

Many people are drivers and spend a lot of time behind the wheel. You don’t always have to drive, sometimes you can just be in the car, waiting for someone, to keep the children busy watching cartoons, it’s convenient to have a phone cradle that can be used specifically for the car.

It would seem that only purchased stands are suitable for solving such a problem, but this is not so; such a stand can be made with your own hands. There are many ways to do this: use Velcro, paper clips, wire, screws and nails, metal stands and many other materials. Each idea has its pros and cons, advantages and disadvantages, you can get acquainted with them by watching a selection of videos:

Cardboard phone or tablet stand

Cardboard is an excellent material that is widely used for various homemade “things”. Probably, many people have a cardboard box or an unnecessary sheet of cardboard at home. It’s worth trying to use it to create a stand.

To do this you will need:

cardboard
scissors

From a sheet of cardboard folded in half, cut a strip measuring 10 by 10 cm. Then draw the figure shown in the figure on it and cut it along the contour.

You will get a comfortable and stable stand that you can carry with you.

This holder option can be used for a tablet or book. The essence of manufacturing is the same, you just need to adjust the part to the size of your gadget, as shown in the figure.

It is necessary to use cardboard that bends well so that the stand does not “open up”.

It is important to understand that a cardboard stand is not necessarily a sloppy brown structure. It can be stylish, comfortable and beautiful. You just need to change the shape a little and the result will change dramatically.

Paper technology

If the stand can be made from stationery clips, then you can also try from paper. For this you will need:

thick sheet of paper;
ruler (minimum 20 cm);
scissors;
pen;
optional paints and varnish (water-based).

Creating an interesting stand for a smartphone will take no more than 20 minutes; origami techniques will be used to make it. The result will be such an unusual thing.

The first step will be to mark on the sheet with a pencil or pen - whatever is at hand, a square shape of 20*20 cm. This is the size of the stand for standard smartphones. Next, cut along the contour and get:

You can use either a regular thick sheet of paper or a cover from a notebook, notepad, colored cardboard, etc. The format is suitable A4.

Next, the sheet is first folded horizontally in half, then vertically. The folds should be pressed down well so that they can be used in the future. Having finished with this, we unfold the sheet with clearly defined outlines of horizontal and vertical lines.

Related article: Crocheting a neckline: learning how to crochet in different ways with videos and photos

For ease of use, let’s mark where our left side is and where our right side is. We take the left edge and wrap it until it rests in the middle of the sheet.

We do the same with the right edge. As a result, we get a sheet that looks like this:

The next step is to create triangles from what we have so far. To do this, one of the corners, upper right or lower right, it doesn’t matter which one you start with, you need to turn it towards the middle, you get a diagonal line. Here we will need a ruler, since the paper in several layers becomes quite dense, it is convenient to smooth and align the fold line with a ruler.

As a result, the paper will look like this:

We do everything in the same order with the left side. The top of the left side is folded towards the center, then the bottom of the left side. After all the folds are put in order, we get:

We bend the new formed corners inward - diagonally:

Now, using the accordion principle, the entire structure must be clamped, we begin to do this on the right side:

Now let’s take the left corner and use the same principle to fold the corners diagonally inward.

It turns out a kind of boat:

We take this boat and turn it over, put it on the table:

Next, we press hard on the middle of the structure and, thanks to pre-prepared trajectories, it bends:

So you get a ready-made stand for a smartphone that you made with your own hands.

With its help, you can not only simply store your phone so that it is visible and in a safe place, but also watch videos by setting it in the following position:

Continuing the experiment, you can then paint the stand any color or even decorate it with a pattern. If using watercolor paint, it is best to paint in several layers and allow sufficient time to dry. On top of this, it is best to coat it with a water-based varnish for durability.

Article on the topic: Weaving from rubber bands: toys for beginners on the machine with video tutorials

Wire stand for phone or tablet

One of the budget options, made from scrap materials.

During work you will need:

wire 2-3 mm thick
pliers
wire cutters to cut wire

Everything is done as simply as possible: in the right places the wire is bent so that it becomes a holder.

To make the structure more stable, the wire can be connected with a rubber band.

Such a stand can be a real design solution: you can paint it a different color and it will be completely transformed, or you can fill the “voids” with decorative wire curls. This design is suitable for both a phone and a tablet, the only difference is the size of your gadget.

Unusual Lego phone stand

Probably, this version of the stand will especially appeal to teenagers and men. Here you can show your imagination by creating a whole complex for your smartphone with the ability to change position, and maybe even amplify the sound of the speaker, or get by with a minimum of details. The creative process will not only bring pleasure, but also bring benefits.

To make such a design, you will need several parts and a base. The level of inclination can be changed by adding or removing parts. And the position of the gadget is easy to change, also adjusting the design.

How to make a stylish phone stand out of a paper clip

Good day, dear readers! At least once, a situation has happened to you when your hands are tired of holding a smartphone, but there is no stand under your hands.

The fastest and cheapest way is to make such a design yourself. That's why we'll tell you how to make a phone stand out of a paper clip. Interesting to know? Then let's get to work!

Set of tools

So, all you need is nothing:

Two paper clips;
Pliers;
A plastic card or something similar of the same size or smartphone size;
Super glue.

In addition to this, you can create special clamps for the device so that it does not fall out of the structure, or secure it at the corners with rubber bands, as can be seen on many photo covers for tablets.

In general, there is room for your imagination to run wild.

Phone stand from an old cassette player

Perhaps someone has an old cassette player lying around at home. It is unlikely that it will ever be useful, and with the advent of disks and electronic media, no one uses cassettes anymore. But still, you can find a use for the cover in which the cassette was located.

To do this, just “turn” the cassette player inside out, tilting the lid back. The hole in which the cassette was held can accommodate a telephone. The advantages of this design are that it is easy to wash and transparent.

Phone stand made from a plastic bottle

Many of us go on a trip or run errands by train. Often, on trains there is nothing near the sockets where you can securely place your phone. However, the gadget is discharged and needs to be charged. You can simplify this task by using a stand made from a bottle. Its essence lies in the fact that the gadget is placed in the cut off bottom of the bottle, which remains hanging on the plug from the charging device. This way, you don't have to stand nearby and hold the phone in your hands or look for a way to secure it.

To make such a stand holder you will need:

plastic bottle for shampoo or drink
scissors

First, wash the bottle to remove any remaining makeup or soda. Then, mark it. The back wall of the stand should become a kind of handle on which the phone holder will hang. The front wall should be high enough so that the phone does not fall over the edge. The next step is to cut out the stand along the office.

To do this, it will be more convenient to use a sharp stationery knife.

Cut a hole in the top of the handle so that it can be attached to the charger plug. You can decorate the stand to suit any taste: using adhesive paper, paints or stickers.

Stand for mosquito repellent tablets

If you don’t have a fumigator at hand, and annoying mosquitoes interfere with your sleep, take a medium-sized binder and hold the edge of a mosquito repellent tablet in it.

Now squeeze the metal staple with two fingers and remove it from the binder. Do the same with the second bracket.

The larger the clamp, the wider its bottom, and the more stable the stand will be.

Light the top edge of the tablet and let it burn well, then carefully extinguish the fire. A smoldering tablet will fill a room, camping tent, or car interior with smoke that will quickly kill those pesky bloodsuckers.

This stand can only be installed on a flat, flat surface. Otherwise, the tablet may fall and burn something.

We recommend: 5 common causes of sewer blockages - a plumber's story

Wooden phone or tablet stand

If you want to make an original stand, then one of the good materials for making it is wood. Such a stand will be strong, durable, and can also serve as a good gift for a loved one. It is important to understand that working with wood requires some minimal skills and special tools.

In the process of work, in addition to a wooden block, you may need materials such as:

saw
jigsaw
sandpaper
wood cutting knives

Be careful and attentive when working with such tools.

Stages of making a stand:

Process the wooden block by sawing off the excess parts and making a recess at the top in the middle for a phone or tablet.
Using sandpaper, remove all roughness and splinters from the surface of the future holder.
You can coat the finished product with varnish or special paint.

Another option for a wooden stand for a phone or tablet is an analogue of its cardboard version. In this case, it is better to use plywood instead of a wooden block.

To do this, make a stencil of the “legs” of the holder and a crossbar that will fasten them together. And transfer it to the plywood. Carefully cut out with a jigsaw and smooth out any unevenness and roughness with sandpaper. Using super glue, connect the legs and the crossbar.

Phone stands: best ideas

A phone stand can be made from the most unexpected materials. We have prepared for you the most interesting ideas and master classes with photos and videos, with the help of which you can easily make this useful accessory with your own hands. Stands made from paper clips, a sheet of paper, corks and other simple things - everyone will find a suitable option for their phone.

Earlier we told you how to make a popsocket. This is also a kind of phone stand. We recommend you look at this collection of ideas.

Paper clips

Using paper clips, you can make a great DIY phone stand in just a minute. This is very convenient when you need to watch something during any other activity, but you don’t have a popsocket or any other stand at hand.

We will need:

any cardboard;
2 clamps.

Just attach them on both sides and the stand is ready. The phone will be firmly fixed in the “ears” of the paper clips.

This device can be used as a tripod. The holder is useful for taking group photos when you have nothing at hand.

Shell

You don't even need special instructions here. The main thing is to find a suitable shell from which you will make a phone stand. It should be big enough.

You will also need liquid nails or rubber glue that hardens into an elastic, plastic mass. If this is not available, you can use acrylic plasticine - it will not stain anything.

To make a phone stand, you need to apply a layer of this glue to the place where the gadget will come into contact with the surface of the shell. If it is not stable, glue can be applied to the bottom to firmly fix it.

This homemade mobile phone stand looks very beautiful and will fit into any interior.

See also: shell craft ideas

Beautiful jar

The simplest stand for a mobile phone can be made from an ordinary can. The main thing is to choose the appropriate size and design.

Choose a jar into which the phone fits freely and does not tip over under its weight. If the source does not look too pretty, arm yourself with acrylic paints. With their help, you can make a beautiful phone stand with your own hands. Paint it in an original way, add splashes or patterns, or any inscription.

You can decorate the jar with twine or braid.

Wine corks

Don't throw away wine corks - this is a great material for creativity! They make just a great stand for your smartphone. Durable, environmentally friendly, beautiful, comfortable.

We will need:

20 wine corks;
Super glue;
lace;
leg-split;
any decor.

Glue the corks together in columns and in a row. First, assemble the pieces for the back wall. Then glue the front completely. The bottom of the stand is glued gradually. Place the plugs against each other one at a time. Then lean against the back wall.

For beauty, you can add lace, thin twine or floss threads and any cute little things.

Bamboo chaise lounge

A very interesting option for a phone stand is a homemade mini chaise lounge. It looks creative, and you can make it at home in just a few minutes.

We will need:

bamboo mat;
bamboo sticks;
6 coffee sticks;
any paint;
wire cutters;
glue gun

Watch this short video master class, in which the author shows step by step how to make an original stand for a mobile phone with your own hands. The result is a bright, stylish accessory that can be used to decorate your desktop or even give as a gift to someone.

Origami

How do you like the idea of making a phone stand out of just paper? Previously, we told you in detail about the origami technique and its basic principles. We recommend reading our material on this topic, especially if you are a beginner.

For this craft, you only need a sheet of thick paper.

Watch the video tutorial in which the author makes a cool stand for his phone or tablet with his own hands. Repeat after him - it's quite simple. This accessory can be easily made in an office, university or school to use a mobile phone for reading or watching videos.

Simple and beautiful

The simplest phone stand without glue can be made not only from paper clips. You will need a plastic mayonnaise bucket and scissors, and the rest is a matter of taste. It is better to choose the most dense base so that the phone is securely fixed.

A step-by-step master class is shown in the video below. You can decorate the craft with acrylic paints, markers, stickers, glitter and anything else.

We hope you were able to choose a suitable master class to make a useful accessory for your phone. Each of them can be modified, improved or customized. Your coasters will turn out beautiful, original and very comfortable.

DIY stand case for your phone or tablet

The most popular option for a gadget stand is a stand case. You will have to tinker with it a little, but the result is worth it. This option is convenient to take with you when traveling, it is durable and can protect the screen.

To make such a holder you will need:

facing material, it is best to choose leather
material for interior cladding
plain and thick cardboard or rigid material
elastic band for fastening
pencil
ruler
scissors
glue
double sided tape

How to do it?

Cut the cardboard according to the size of the tablet so that it completely covers it. This is the future basis, the dimensions of which will be basic for all elements.
Make several folds in the same way that the front of the case will then need to bend to support the tablet.
Now we take hard material, which will give the case stability. We cut it so that it follows the contour of the workpiece.
We apply it to the base and make an edging so that it does not interfere with the folds.

From the inside we treat the case with soft materials, gluing it to the base blank with double-sided tape.
The next step is fastening for the tablet itself. To do this, we make small holes in the rigid elements for elastic bands that will hold the tablet.

We glue the finishing material on the outside.

Do this as carefully as possible. The appearance of the product will depend on this.

That's all. The stand is ready! It is convenient and can be used not only as a holder, but also to protect the screen.

Stand-bag for tablet or phone

An original and cute version of a gadget stand. It is suitable for girls and can be a cute home accessory.

To make it you will need:

scissors
textile
padding material
thick cardboard
thread and needle
button

Manufacturing process:

First you need to cut out a template from cardboard according to the size of your gadget.
Then cut out a rectangle from the fabric twice the size of the resulting template.
Fold the fabric base in half and mark with stitches a fold 10 cm from the edge.
Sew the bag, leaving one side unsealed.
After turning the bag inside out, position it so that the seam runs through the middle and a diamond shape is formed at the end. After ironing it, bend the top corner of the diamond so that it is in the middle and sew. This is shown in more detail in the figure.

Then insert cardboard into the product and fill the remaining space with padding material.
Make a seam along the very edge of the template. Folding the edges of the unstitched side, carefully stitch it, leaving an opening for stuffing.
Make a roll and sew up the hole.

That's all. The product is ready. You can decorate it to your liking, giving it even more charm!

Phone stand made from paper clips

Another interesting and at the same time very simple option. If you have several office clips at home, then feel free to use them!

You will need 2 clamps: one larger and the other smaller. By connecting them together as shown in the figure, in a couple of seconds you will get a phone holder.

This can also be done from two clamps of the same size.

Phone holder on the table: 7 super quick options

Merilyn

1712 0 0

The stand is convenient for viewing videos and photos on your phone

A phone stand is a convenient gadget: it frees your hands while reading, viewing images, videos, and playing games. There are many ways to quickly make phone holders. I offer the most comfortable and lightest ones - from scrap materials.

Option 1. Stationery binders

There are several ways to make a holder from office clips/clips. They provide stability. You can take any quantity for production.

If you construct a mount from several clamps, the stand turns out to be convenient, but cumbersome. I'll tell you how to make a stand from a minimum number of clips.

One clamp. To do this, you need to make a “bed”: slightly bend the metal part of the clip towards the installation of the phone.

Bent eye of the clip

Stand option for the lazy. You don't need to do anything, just find one clip. Pinch the edge of the case on one side and place the phone on the table.

The location is convenient for placing the phone horizontally

Two clips and a strip of thick paper. The size of the sheet of paper corresponds to the size of your smartphone.

Option for video shooting, as the stand is stable and its tilt is adjustable

Two clamps . They are fastened so that one remains open. For reliable fixation, the lower, open end is bent or a piece of pencil eraser is inserted into it.

The ear of the clip needs to be bent

From two clamps you can make a stand in 5 seconds . Place the small pen in the open large clip. Close the clamp and the stand is ready. It is compact, does not take up much space, and can be carried in your pocket.

I offer a detailed description of the steps to make the simplest smartphone stand. The table shows the steps.

Photo	Execution steps
	Step 1 Find or buy two clamps of different sizes. The price of two clips is about 10 rubles.
	Step 2 Attach the clips as shown in the photo. The small binder is captured by the larger one.
	Step 3 Place the phone on the resulting support.