How to raise a bed higher off the floor

BEDTIME TABLE FOR ACTIVITIES

This bedside table is wide and durable enough, which means it is convenient for doing any kind of work.
For some, a recess in the working surface of the table will help, as it will allow you to sit closer to the table and provide support for your hands. The notch is shown in the figure with a dotted line. It is impossible to recommend exact dimensions as they depend on the height of the bed and the body characteristics of the person sitting in the bed. Determine them yourself. Material A. Table top - plywood 9 mm x 400 mm x 600 mm. B. Long table top strip - softwood 12mm x 50mm x 600mm. C. Short table top strip - softwood 12mm x 50mm x 200mm. D. Load-bearing slab - plywood 9 mm x 400 mm x 760 mm (dimensions are relative). E. Short bars - dense wood 25 mm x 25 mm x 350 mm, 2 pcs. F. Long bars - dense wood 25 mm x 25 mm x 760 mm (dimensions are relative), 2 pcs. G. Side walls - plywood 9 mm x 200 mm x 760 mm, 2 pcs. N. Side bars - dense wood 25 mm x 25 mm x 150 mm, 4 pcs. I. Base - plywood 9 mm x 400 mm x 760 mm. And. Skids - dense wood 25 mm x 40 mm x 760 mm, 2 pcs.

Fastening with glue and screws.

Operating procedure1. Fasten parts A, D, J, I, as shown in the figure. 2. Attach the sides to the base plate D. 3. Round the edges of the runners as shown in the picture. 4. Attach base I to complete the base plate assembly. 5. Attach the tabletop. 6. Sand and paint.

Bed under the podium

Yes, the disadvantage of a wardrobe bed is that you need to secure the bed with rubber bands so that it does not roll off when the bed is folded. But if you hide the bed in a podium, you don’t even have to make the bed.

The area of this full-fledged apartment is 15 square meters. If it weren’t for the bed, which slides into the podium under the kitchen, it would be completely impossible to turn around. The bed can also serve as a sofa if pulled out halfway.

And this apartment for a young girl fit on 12 square meters!

BEDTIME TABLE ON IRONING BOARD

Perhaps the idea of making a table on an ironing board, at least temporarily, will seem successful to you. This board can also be installed along the bed, then you will have a long table. When the table is not needed, the board can be easily removed.

MaterialA. The base is plywood 6 mm x 250 mm x 350 mm. B. Front strip - softwood 10mm x 50mm x 350mm. C. Side strips - soft wood 10 mm x 50 mm x 1 90 mm, 2 pcs.

Fastening with glue and screws.

Procedure 1. Attach front panel B to base A. 2. Attach sides C to base A. 3. Sand and paint.

Low ceiling is not a problem

Owners of rooms with high ceilings are lucky - but what to do if they are low? The same thing: place storage systems under the bed.

And in this tiny apartment there was even room for a refrigerator under the bed!

HOW TO INCREASE THE HEIGHT OF A METAL BED

Since drilling and attaching metal or wood to a metal bed is difficult, it is easier to place the bed legs in small wooden boxes. This method of stand can be used for any bed, especially if you need to give the bed its original height.

MaterialA. Base - plywood 9 mm x 90 mm x 90 mm, 4 pcs. B. Smaller sides - plywood 9 mm x 72 mm x 1 50 mm, 8 pcs. C. Large sides - plywood 9 mm x 90 mm x 150 mm, 8 pcs. D. Block - strong wood, area corresponding to stand x required height. E. Forged wood screws No. 8 x 25 mm.

Fastening with glue and screws.

Operating procedure1. Drill holes for base A and sides C. 2. Drill auxiliary holes in sides B with a diameter equal to half the diameter of the screw. 3. Attach sides B to sides C. 4. Attach assembled sides B and C to base A. 5. Sand and paint to match the bed or seal. 6. Cut the blocks to the required size.

Wardrobe bed

What if you hide the bed in a closet? Buying such a model has not been a problem for a long time. By the way, the area of this apartment is only 6 meters! Hidden behind the green doors is a closet and a small but much needed shower.

Another version of a bed pretending to be a wall was chosen for a student girl’s micro-apartment. The berth reclines like the top bunk on a train. A work desk is hidden in the closet, and a table and poufs are hidden under the sofa.

WOODEN STANDS FOR WOODEN BEDS

This way to increase the height of the bed is simple and effective, but take the time to choose the material. The wood must be well dried so as not to split under the weight of the bed itself and the person lying on it. Glued sheet plywood is suitable for this purpose.

Material A. Extensions - well-dried wood, diameter approximately equal to the diameter of the bed leg, length - the height to which the bed needs to be raised + 150 mm, 4 pcs. B. Nuts and bolts - approximately 5 mm, 8 pcs. C. Washers - as large in diameter as possible so that the wood does not split when the nuts are tightened.

DIY bed made from construction pallets

The most budget-friendly material from which you can make an original bed is construction pallets. They can be purchased at a bargain price; the only thing is that the wood will be second-rate, but if you plan to decorate the bedroom in a loft or rustic style, then such texture and knotty wood will only be a decoration.

Despite the cheapness and strength of this material, it is worth remembering that it is not suitable for point loads, which means that you cannot jump on it. Also, second-grade wood is very sensitive to moisture, so it is better not to install such a bed in an unheated and damp dacha.

In all other cases, this is an endless field for creativity, because such material is very malleable, you just have to apply your hands and imagination. How the craftsman did it in the next video.

METAL STANDS FOR WOODEN BEDS

The stand made from angle steel or angle aluminum is very durable. It can be installed quickly.

Material A. Extensions - sheet iron or sheet aluminum, dimensions calculated in the same way as the dimensions of a wooden extension, 4 pcs. B. Nuts and bolts - about 5 mm in diameter, 16 pcs. C. Large washers - 32 pcs.

Operating procedure1. Round all edge corners of each A extension. 2. Drill the bed legs and A extensions to fit the nuts. 3. Bolt the extensions to the bed. 4. Paint to match the bed.

How to make a podium for a bed with your own hands

The use of non-standard architectural solutions when decorating the interior of a room largely determines the attractiveness of its appearance. Such techniques include multi-level ceilings or niches in the walls. The recently popular bed podiums also add originality to the design of the living space. In addition to the aesthetic component, such designs also have a functional purpose.

How to make a podium for a bed with your own hands

TABLE OVER THE BED

This table can be made by anyone who has a good workshop and the necessary tools. The table is designed for a wide variety of activities and work. It can be equipped with a vice, electrical outlets, a lamp and used as a workbench.

To determine the size of wooden parts, you need to know the width of the bed and the distance from the tabletop to the floor.

MaterialA. Tabletop - plywood 9 mm x 400 mm x length. B. Backstrap - softwood 10mm x 50mm x length. C. Side strips - soft wood 10 mm x 50 mm x 390 mm, 2 pcs. D. Legs - soft wood 10mm x 45mm x 45mm x height, 4 pcs. E. Long Top Rail - Softwood 12mm x 75mm x Length, 2 pcs. F. Short Top Rail - Softwood 12mm x 75mm x 310mm x 2 G. Bottom Rail - Softwood 12mm x 75mm x 310mm, 2 pcs.

We do not give any assembly instructions here, as an experienced craftsman will know how to assemble all the parts. You can determine the size of the table top, back bar, legs and long crossbars by calculating the length of the table top based on the width of the bed, and the height of the table based on the position of the person in the bed. The length of the tabletop is equal to the width of the bed + 200 mm, the height of the table (to the inside) is the measurement taken when the person is in the bed and sitting in the working position.

Bed - second tier

Further more. The bed moves to separate functional areas, thereby creating a second tier in the apartment.

The owner of this apartment had a very small budget and was forced to buy a tiny apartment. To save space, the bed was placed on top of the wardrobe, and in order to save money, the wardrobe has not even been closed with doors yet - the girl will be able to finish the renovation later, when she has saved up money.

And in this apartment they created a whole room within a room: the second floor is a bedroom, and on the first floor there is a work area, a dining area, many storage systems and even a folding bed in case of guests.

Here the bed is located on a deep closet, and a kitchen block is attached to the side.

The designers of this small studio apartment took advantage of the height of the ceiling and built a bedroom on the bathroom. Despite the modest dimensions for an isolated apartment (24 sq. m.), the room seems huge and light, which would never be achieved by placing a bed, sofa, many closets, a workplace and a kitchen traditionally along the walls.

What height should the bed be from the floor for maximum comfort?

Everyone knows that adequate sleep has a great impact on human life. Well-being, mood, and performance depend on the duration and quality of night rest. The bed occupies a dominant position in this process. Its technical and quality characteristics provide comfort, relaxation, and aesthetic pleasure for the vacationer, thanks to which a quick immersion in sleep occurs. At the same time, all parameters are considered significant, from finishing to mattress. In today's article we would like to draw your attention to the height of the bed. At the selection stage, little attention is paid to this factor. In most cases, a miscalculation with height is discovered when the furniture is already installed in the bedroom. We suggest you find out what height standards there are, and how to choose it correctly, in relation to your height.

Average bed height above the floor

When making a choice, take into account the person’s age and height. But there are standard indicators that you can focus on. First, let's look at typical data for children. Children usually buy furniture with a guard that protects them from falling. So beds with a side should have a height of half a meter. Products without guards, designed for children over 3 years old - 30 cm.

For adults in different countries there are standard indicators:

The largest of them in America are 80-100 cm. The tradition of making such furniture dates back to the times of the colonial style. Thanks to the sufficient height, drafts did not annoy those who slept on the bed.
The minimum height of a bed in the east is 20-30 cm. Also, the tradition has been preserved since ancient times, when a kind of podium was used as a sleeping place in Asia. Because of this, modern furniture has acquired forms familiar to the East.
The optimal values in Europe are 50-60 cm. They are designed for average data and are suitable for most people.

Why is it so important to pay attention to the height of the bed?

The height of the bed from the floor is no less important than its design or the choice of mattress. A product that does not correspond to a person’s height causes discomfort when used, and in some cases even harms health. So, for older people, a low base is fraught with problems with the joints; moreover, they will not be able to get out of bed or lie down on it without the risk of injury. An elevated bed is dangerous for children, and deprives adults of support under their feet. A loft bed, with a height of more than a meter from the floor, is safe in itself, but if it is installed in a room with low ceilings, the likelihood of shortness of breath and oxygen starvation increases. That is why it is important to pay attention to the elevation of the sleeping place and compare it with height, age, and accommodation conditions.

Regarding the elevation itself, it should be noted that it is formed from two indicators: the level of the bed above the floor and the height of the mattress. The latter can significantly affect the level of the product. Depending on the filling, the mattress can reach from 15 to 30 cm in height, and custom-made models reach up to 50 cm.

Bed on the podium

Recently, creating bed podiums has become a fairly common hobby among owners of small apartments. And this is understandable, because in this case two birds with one stone are killed, and the sleeping area turns out to be quite spacious and the storage system is ready.

Moreover, to create it you can use any material, including elements of old furniture or shelves and cabinets. Sometimes part of the room is covered with a podium, and then you get a multifunctional area with a wonderful sleeping area and an office/living room or playground for a child. There are a lot of options, it all depends on the purpose of the room and the need to seal the living area.

What height standards are there?

According to GOST, the height of sleeping products is prescribed only for children's furniture. It is 50 cm from the floor for cribs with guards, and 30 cm from the floor for products without guards (intended for children over 3 years old). Regarding adult furniture, there are no regulatory restrictions. Each manufacturer, at its own discretion, sets the optimal distance from the floor at which the legs of an adult in a sitting position have support, and in a lying position he does not feel drafts walking along the floor.

However, there is a so-called global gradation of the height of sleeping products. It consists of three categories:

European standard (assumes an average level of rise above the floor, from 50 cm to 65 cm);

Asian standard (under the influence of the culture and way of life of Asian countries, furniture of this standard has a height of 20-40 cm from the floor, without a mattress);

American standard (the largest, like everything in America. The height of the bed is at least 80 cm from the floor, and in some models it reaches one meter).

Manufacturers are guided by this gradation, creating furniture of a certain style and design. Thus, classic beds usually have a height of 50-60 cm. Oriental-style beds (daybeds, ottomans, minimalist podiums, bamboo beds) are traditionally low. And the huge, square boxes are in the American style, and the height is appropriate (more than 65 cm). This division occurs by default, i.e. one manufacturer will not, at its own peril and risk, make an ordinary European bed high. But if the customer so wishes, please, for an additional fee, the furniture makers will make a bed even according to your own sketch. In the showrooms, models with familiar, world standards are exhibited.

Peculiarities

The height of the bed is influenced by the height of the footboard (tsar), the height of the base of the berth and the height of the mattress. For such a parameter as the height of the bed, there are certain standards. Thus, the European standard implies a distance from the floor of 50-60 centimeters. According to the Eastern standard, this value is 20-30 centimeters, while the American version states that the bed should be at a distance of 80-100 centimeters from the floor.

If you are at a loss as to what height to choose for you, here are a few things to think about. Know that it is easier to get up from a high bed. Therefore, if you are purchasing a sleeping place for an elderly person, consider buying a high bed.

Those who have small children in their family need to be extremely careful when having a high bed. After all, it is known that children are very mischievous and jumping on the bed is a great pleasure for them. For many children, a meter high can be simply hazardous to their health.

A big plus of a high bed is the ability to use the area under the bed for storing things. High beds often have just huge drawers that can be used successfully. There are also options for such beds with lifting mechanisms.

Low, on the contrary, is safer if you have the habit of sleeping with small children in your bed or buy it for your child. After all, there is always a risk that you may not notice and the child may fall off it. However, this choice is unlikely to be suitable for older people, since getting up from a low bed is very difficult. But, of course, all this is individual.

It is also worth paying attention to the fact that a low bed is very close to the floor, so in order not to breathe dust, you will have to take more care about hygiene.

The gold standard when choosing a sleeping height is that if you sit on the bed with your feet on the floor, the angle under your knees should be straight. This will be the optimal bed height for you. Everything else is a matter of taste, habit and personal preference.

Of course, there are models of beds with adjustable beds, but they have a medical purpose and are intended for hospitals.

In children's versions, you can adjust the height by setting its bottom at different heights , of course, if such an option is provided for by the design. In this embodiment, the bottom serves as an increase in the height of the berth.

As mentioned above, the height of the bed also consists of the height of the mattress. There are spring and springless models of mattresses. In the first version, their height usually reaches 20-25 centimeters. The second option has a height of 15-20 cm. There are also very thin mattresses up to 7 centimeters high. They are usually used for shell beds or placed on cots.

How to choose the optimal bed height

What height is optimal for a bed? There is no clear answer to the question. It all depends on the individual characteristics of the person. If the style of bedroom furniture is of secondary importance for you, and first of all you want to choose the most comfortable, convenient bed, the European standard will be ideal. It is designed for the height of the average European (170-180 cm). Tall people (200 cm and above) are recommended to choose American standard furniture. The described parameters also need to be correlated with age. So, for a tall but elderly person, a bed with a large rise will not be suitable. There is a risk of injury associated with age-related incoordination and reduced reaction speed. A low bed is also inconvenient for a person of advanced age to rest, but it is considered suitable for children. Children's sense of boundaries is poorly developed; if they sleep on a bed without sides, it is better if it is low.

You can determine whether the selected stock has the correct height without a tape measure. It is enough to come close to your favorite model and see at what level the base with the mattress is located. The ideal option is when the mattress is at knee level. If the bed is not equipped with an orthopedic base, the side of the bed, ending just below the knees, can be considered the norm. A double bed that will be used by people of different heights should be a happy medium for both. One of the best options, again, will be European standard furniture. It will not allow a tall person to sink too low and a short person to climb up.

How to raise a bed higher off the floor

In small one-room apartments, you have to save every centimeter of living space. How to arrange a small home, a one-room apartment, so that the necessary areas fit in - kitchen, living room, bedroom, and have some free space left?

An excellent solution in a room with a high ceiling is a sleeping mezzanine or a hanging bed under the ceiling. How to implement such ideas, photos of interesting solutions, tips on how to make a structure with your own hands - this will be discussed in the article.

Do-it-yourself mezzanine bed - how to plan?

If the ceiling is high, an excellent solution that saves room space is a bed on the mezzanine. The correct design of the mezzanine gives the bedroom a unique character and the room becomes functional. It is important to properly plan the design of the mezzanine, determine the cost in advance, and find out the possibilities.

The mezzanine is a universal solution, perfectly presented in small rooms and spacious houses where there is no shortage of space. The possibilities of the mezzanine are great; it can be organized in almost any room:

living room;
bedroom;
children's room

In which room can a mezzanine be made?

The height of the mezzanine on which the bed is planned must be at least 120 centimeters. If the height is less, it will be uncomfortable. The optimal height for comfortable use is chosen in accordance with the height of the people using the room, usually 1.8-2 meters. This design allows you to walk underneath it freely.

In high rooms, with ceilings of 4 meters, it is convenient to organize a mezzanine structure in the form of a mezzanine. It is convenient to use the bed and the space below by organizing:

recreation area;
cooking area;
working mini-office.

Hanging double beds on the mezzanine, photo

You can create an ideal cooking area under the mezzanine, or create a wonderful sleeping bed in the attic. In the photo below, the kitchen is illuminated by halogen bulbs installed on the mezzanine.

Under the mezzanine the ideal space has been created for a small, comfortable kitchenette. The cabinets are made to order from painted MDF boards. The 3 x 2.4 m mezzanine is so large that access to the mattress is provided from 2 sides.

The mezzanine provides enough space for 2 bedside tables with lamps, providing the necessary light for reading.

The next mezzanine bedroom, with a height of 110 centimeters, is a little low for walking, but sufficient for lying down and sitting. One wall is finished in oak paneling with shelves replacing bedside tables. Illumination is provided by a lamp attached to the shelf.

The next bedroom, located on the mezzanine, is high (1.8 m), allows free movement, includes a bed and desk. The ingenious headrest above the mattress attracts attention - soft panels are glued to the wall.

The next mezzanine is located above the hallway and kitchen. There is a simple wooden oak staircase leading up to it, similar to the wood from which an antique kitchen cabinet was made.

Approximate price

The cheapest offer is wooden children's beds located under the ceiling, measuring 90 × 180 centimeters, the height does not exceed 1.3 m. A pine bed costs 25,000 rubles. An additional expense is the purchase of a mattress; the cost of a cheap mattress is 2000-3000 rubles. Models made from MDF can cost a little cheaper or more, depending on the quality of the material and design.

Models with dimensions of 90 × 200 cm and a height above 1.6 m will require a little more expense. The structures are conveniently used by children and adults, and are equipped with stairs and steps. Such models cost from 30,000 rubles.

More expensive models include:

The stores offer a wide selection of models. Under the mezzanine there are multifunctional tables, cabinets, and shelves. Beds measuring 90 × 200 and 1.8 m high cost from 35,000 rubles (depending on the type of equipment).

Large expenses will be incurred by installing a mezzanine with a double bed (minimum width is 140 cm). This type of mezzanine is made only to order according to the size of the room. The area under the mezzanine is used to place furniture and as a practical seating area. It all depends on the needs of the residents, the size, and characteristics of the room.

How to make a mezzanine?

In the manufacture of load-bearing structures, wood and steel profiles are usually used. A separate small bed, located on the mezzanine, is additionally secured to the wall. To climb up, use ladders of simple designs, as for ordinary bunk beds.

Large structures are complemented by large staircases, for example, spiral ones. For safety reasons, it is recommended to use stairs with handrails for children.

Lighting

A sleeping mezzanine is a great addition to many apartments. The design allows you to save space and arrange a one-room apartment or room in an original way. You need to keep in mind your specific lighting requirements.

If the room has a mezzanine, you should not install intense ceiling lighting.
Directional lamps that do not blind a person lying on the bed are better suited.
You need to think about soft lighting for the mezzanine (above and below).
A small bedside or LED strip should be installed near the bed.

Remember! An appropriate level of lighting will significantly improve the appearance of the bed and increase functionality.

Bed with lifting mechanism

There are other solutions. This is a special bed with a lifting mechanism that allows you to lift the bed up and free up space in the living room.

The simplest Compact Basic model uses a mattress with a rigid frame, as standard, the legs do not fold. You can use a standard mattress. There are models with folding legs that automatically unfold when the structure is lowered.

Safe use of furniture will be ensured by certain conditions:

from floor to ceiling there should be a distance of at least 2.25 m, no more than 3.25 m;
the bed should be attached to the floor, ceiling;
the difference in floor level between the legs should be no more than 4 cm, between the legs and the lifting column - no more than 6 cm;
elements of the room should not be placed in the path of the structure between the floor and ceiling;
in the case of side folding, the berth will lean against the wall or other elements of the room, preventing its destruction; if this condition is not met, it is necessary to install additional rails that strengthen the structure;
availability of a suitable mattress on a wooden frame.

Differences between bed legs, their main characteristics

Supporting fittings play an important role in the production of cabinet and upholstered furniture. The products are responsible for the stability, reliability, and service life of structures. At the same time, bed legs perform a practical and decorative function, the quality of which is subject to special requirements. The supports must be made of durable, high-quality material, securely connected to the base (frame) of the bed, and match the design and style of the furniture.

Decorative elements

Decorative elements play a big role in finishing the product; thanks to them, the bedroom will sparkle with new colors. One of the options for finishing elements is wooden slats, 5 by 2.5 cm thick, which should also be included in the drawing.

Manufacturing process:

it is necessary to make the required size of slats from the prepared materials;
the prepared slats must be sanded and painted with stain, the color of which is chosen based on personal preferences and the design of the room;
after drying, they are coated with water-based varnish;
After opening the first layer of varnish, you need to sand the slats to prevent the appearance of all kinds of bubbles. Next, apply two more layers of varnish;
The painting procedure must also be carried out with the legs.

Fastening:

decorative trim is attached with glue;
it is necessary to apply glue to the surface of the frame and finishing slats;
using clamps, press them for a while, preferably until the glue dries completely;
all excess glue must be wiped off with a damp cloth;
The slats can be fastened using either nails or self-tapping screws.

Fastening the lifting mechanism requires additional skills, since its installation must be of high quality and safe. There are three types of mechanisms, each of which is installed differently. Therefore, having chosen a certain type, you need to carefully study its installation diagram or seek the help of specialists.

Why are they needed?

In the production of bedroom sets, different types of supporting fittings are used. The legs ensure the stability of the sleeping place and allow you to adjust the height of the frame relative to the floor level, taking into account the personal preferences of the person who sleeps on it. The presence of legs gives the furniture interesting decorative touches. Since the bed occupies a central place in the bedroom interior, the design of the furniture attracts attention. Bed legs perform several important functions:

reliable stability - the frame is clearly fixed and takes on the load of the body weight of a sleeping person;
protection, functionality - furniture with supports can be conveniently rearranged, excluding mechanical damage, and adjusted in height;
decoration, design - with the help of legs you can emphasize the style of the furniture design;
order, comfort - under furniture installed on supports, it is more convenient to perform wet cleaning and vacuum the carpet.

Varieties

The classification system is quite extensive. They are divided into types according to several parameters: shape, material used for manufacturing, functionality, adjustability.

carved

A lot can be said about the shape of bed legs. It depends only on the imagination of the manufacturer. Each buyer can choose what he likes and is suitable for him - square and round, curly and straight.
Quite a lot of materials are used to make these elements. They can be metal, wood , plastic or even a combination. The material affects overall quality, practicality and durability.
Functions. The material for making the legs, their shape, and dimensions depend on the conditions under which this or that piece of furniture will be used.
Adjustment. According to this parameter, products are divided into two subtypes: those that can be adjusted and regular ones. The first type is used much more often. Such products allow you to customize furniture to suit your needs and preferences. Some people like beds with high legs, while others, on the contrary, like low ones. It is convenient to display furniture this way on a not very level floor.

Difference of elements

Furniture support fittings include an extensive range of bed legs. All products differ in basic parameters - material of manufacture, shape, design, adjustability. The decorative design of the supports can be made with luxurious carvings or without decorations - it depends on the design decisions of the manufacturer. The photo below shows beautiful bed legs of different sizes and designs.

By shape and design

On the furniture fittings market, bed supports are represented by a wide range of products that are distinguished by a variety of designs. All elements should look harmonious, so you should pay attention to the artistic design and shape of the products:

curved supports with decorative carvings, patterns, gilded inserts - an option for classicism, classical style, empire style;
massive, voluminous elements with complex decor from petals, curls, patterns - an idea for lush baroque, sophisticated rococo;
round low legs for the base of the bed, reminiscent of flat plates with a chrome surface - modern;
square and rectangular supports - can be used in retro, ethnic, Scandinavian, country styles;
massive wooden fittings are a solution for the English and colonial style, products with strict geometry for the chalet style.

In bedrooms decorated in high-tech, techno and minimalist interior styles, they use metal fittings or install a bed without legs, the frame resting on the sides or podium.

According to the material of manufacture

Since the supports provide stability to the bed, you should pay attention to the strength of the material from which the legs are made. Plastic, wood, and metal are used in the production of accessories. The advantages of wooden products include high quality material, optimal strength, rigidity, and decorative appeal. A bed with legs for the bedroom looks harmonious in interiors of any style.

Metal fittings are used to organize sleeping places in modern interiors. Chrome-plated, anodized, powder-coated metal protects the material from corrosion and gives the supports an attractive shine and color. Metal legs have a long service life, the necessary rigidity, strength, and resistance to significant loads. To prevent the supports from spoiling the floor covering, stands for the bed legs are installed on the lower part - inconspicuous plugs.

Plastic legs can be mounted on a bed with a lightweight frame. The products are quite durable, do not creak, do not dry out, but have a shorter service life. Mostly they have a simple design, round shape.

Height adjustment options

The sleeping place should be convenient and comfortable. The level of the bed from the floor is determined by personal preferences; the standard height of the supports is within the range of 240-250 mm. If adjustment is possible, fittings are divided into regular and adjustable. Simple legs do not allow changing the level of the sleeping place relative to the floor.

Adjustable bed supports are used more often in furniture production. With their help, you can adjust the height of the structure taking into account your own preferences, and clearly install furniture on an uneven floor. Adjustable models are equipped with a screw mechanism with a wide range of adjustment. The fittings are attached to the orthopedic frame with screws and self-tapping screws.

Loft bed

The simplest and most obvious solution is to raise the bed up. When the bed is above eye level, it seems to be invisible. But below you can place a full-fledged workplace or a comfortable sofa.

Just imagine how much space appears in the bedroom when the bed goes to the ceiling. But before, only a bed, a couple of bedside tables and a wardrobe fit here. Add curtains and a reading lamp - and now a new space has appeared in a small, cozy bedroom.

But it is not at all necessary to place the bed on long legs: for example, 2 cabinets will be suitable as a support. If it weren’t for the bed under the turquoise ceiling, it would be impossible to fit a workplace, a sofa for guests, a huge mirror and even a wardrobe into this 10-meter communal room.

Main requirements

You need to choose a bed thoroughly and responsibly, since the furniture will last for many years. The service life largely depends on the quality of the supporting fittings. The main requirements that bed supports must meet are quality, strength, functionality, ergonomics, and aesthetics. What do these parameters mean:

strength - the support must be made of high-quality material with good performance characteristics;
rigidity - installation of the legs on the frame should ensure the stability of the berth;
practicality - the ability to absorb the required weight loads, clearly fix the frame;
ergonomics - the supports should not interfere with walking near the bed, create squeaks, or scratch the floor covering;
decorative appeal - elegant, massive, carved, patterned, classic legs emphasize the style of the furniture.

The use of supporting fittings allows you to implement exclusive design solutions and set the sleeping bed to the desired height from the floor. The legs serve as a functional and decorative addition to the furniture, simplify cleaning under the bed and give the bedroom interior a beautiful, holistic look.

Don't have enough space in your house? Solution

It is very difficult to create all the conditions for a comfortable life in a small house. Kitchen-dining room, bedroom, bathroom, workplace - areas without which we cannot imagine a modern home. But even in a small area you can not only place everything you need, but also do it in style!

There are practically only three main ways to rationally use space in a small house:

development of space in height - creation of a second tier;
installation of folding multifunctional furniture;
Maximum use of angles.

Here are some striking examples of a creative approach to increasing the space efficiency of a residential building with a small area.

We raise the beds above our heads

The bed usually takes up the most space in the house. And this statement becomes especially obvious when the bed is lifted off the floor, freeing up several scarce square meters. The bed can be raised on racks, or it can be hung from the ceiling!

Creating the second tier

If the height of the room allows, then it is advisable to raise not only the bed, but also the whole tier above the floor, creating almost a second floor.

We use folding compact and multifunctional furniture

In this matter, the imagination of furniture designers and designers has no limits: wardrobe-bed-bathroom, shelves-TV-wardrobe-bed, bed-office-wardrobe, sofa-2-story bed, etc.

Making good use of room corners

The corners of the rooms are usually empty or occupied by something completely useless, while this is one of the most capacious places in the house in which you can place, for example, a corner desk, a TV table or even special corner drawers.

Looking at these inspiring examples, you are convinced that you can live in complete comfort in a small house!

views: 33849 | rating: 238

Download - How to increase the height of the legs of a bed without reshaping the bed itself.

Ivan Baev

Video comments

Good morning, Ivan! Previously, this morning was a holiday, which I don’t even know now, they seem to say it’s a holiday, but personally I don’t feel it. Well, okay, let's finish the lyrical digression and move on to the main thing. The alteration was a complete success, it looks much more interesting. To your comment at 9.50, I would add one more addition: every self-respecting master, and you certainly are one, has a certain bar, to fall below which is not to respect yourself. As usual, Ivan, my wishes for health and good luck, both to you and your family and friends!

There are no hopeless situations in carpentry. There is always the possibility of redoing it. Thank you, Vanya.

Yes, people really no longer respect each other and each other’s work. This is where the problems in society come from.

Hello Uncle Vanya, great job. What I like is that in some situations you can change the design, the main thing is to approach it wisely.

Wow! Grigory gave me some work, he's called a friend

Uncle Vanya is a very cool guy who values and respects the opinions of his friends and this is the most important thing, I always enjoy watching Uncle Vanya’s videos and have learned a lot for myself

You were right about the opinion of your friends, you need to respect it, respect to Gregory, and respect to you, and the bed really turned out more beautiful

Excellent addition-remake! Definitely like. Good luck in your business and good health!

It is difficult to make a good product, and even more difficult to remake it. They say it is better to rebuild a house than to remodel it. But your change was a success. Grigory was right, it will be better this way..

Well done, Uncle Van! Well done! And the armchair critics were walking through the forest! Any criticism is good if it is supported by arguments and comes from the lips of a master. The rest of the sofa specialists only scratch their tongues at the masters, but what’s the point, half of them didn’t even hold a hammer in their hands. Special greetings to Grisha

I looked at it. I completely agree about the oil.

I respect craftsmen who meet the customer halfway, and do not persuade him that “he is a fool himself.” Respect Vanya and respect, and probably everyone has friends like your enemy

That’s why a FRIEND should tell the truth. Be healthy IVAN.

I liked the second option better too.

Yes, Ivan Nikolaevich, there are plenty of smart-ass friends, as long as you stroke the wool you are a friend, as soon as the light goes out a little, you become an asshole at best, or even worse, so don’t pay attention to them. good luck, health, all the best.

Beautiful legs, nice to see :)) Happy May Day!

This is called a rehearsal :)) Now we need to make telescopic legs, this is an idea! If you want to lift it up, lift it up))))

Good health, D. Vanya! Happy May 1st! Well, damn it! I would hardly have dared to do this, and I would definitely ruin it! :-)))

Thank you Ivan. The more I watch, the more I respect it.

Yes, an old horse won’t ruin the furrow. ))) And there is no limit to perfection. ) It turned out beautifully. The middle finger is at work again. )))

⇥ Autoplay

Carriage for round conical legs | DIY | DIY furniture

DIY bed made of wood (blocks and furniture board)

Making a bed. Headboard. Author's work.

Airy, light-looking, open staircase.

Supports, legs for furniture

Standard bed sizes.

Adjustable table legs: simple and fast

Furniture leg manufacturing option

How to make a stool. DIY furniture #1

Types of furniture legs, supports. Possibilities for their regulation

DIY bed. Very durable legs for RUB 143

Making a double wooden bed from A to Z

Bed footrests

After a hard day at work, everyone dreams of quickly relaxing on their favorite bed and being distracted by exciting videos. Any visitor to our site will be able to find an exciting video to suit their taste and interest. Even the most sophisticated viewer will find something worthy for themselves. Our site allows every visitor to watch videos in the public domain, without any registration, and most importantly, everything is completely free.

Making the bed longer

The old bed is a bit short and we'll have to make it longer using the same hardware. New plank bottom, a little paint... and the bed is like new! At a flea market, you can sometimes buy something useful cheaply, for example, old, skillful handicrafts. The new owner was delighted with such a valuable acquisition, but when he collected it, he became thoughtful: it turned out that there was not enough space for mattresses. The bed turned out to be 15 centimeters shorter! And in order for the length to reach two meters, the bed had to be lengthened in the middle and at the ends. New parts are made of fiberboard. And after painting the bed, the joints are completely invisible. The old fittings, which were removed to later be installed on additional parts, also came in handy. They are attached to the new sidewalls with glued dowels and screws.